search.noResults

search.searching

saml.title
dataCollection.invalidEmail
note.createNoteMessage

search.noResults

search.searching

orderForm.title

orderForm.productCode
orderForm.description
orderForm.quantity
orderForm.itemPrice
orderForm.price
orderForm.totalPrice
orderForm.deliveryDetails.billingAddress
orderForm.deliveryDetails.deliveryAddress
orderForm.noItems
Expert By Wayne Colonna ATSG President


Fundamentals or Forgetamentals Part 4 Hyundai


False Solenoid Electrical Codes Figure 1 Figure 2


Figure 3 A


1997 Hyundai Tiburon came to a shop in Chicago with codes P0743 (TCC Solenoid circuit fault) and P0747 (Pressure Control Solenoid “A” circuit fault) stored in memory (Figure 1). This vehicle uses an A4BF1 transmission and was not in limp mode. The “MIL” was illuminated with no apparent driveability complaints.


As a time-saving procedure (so he thought), the tech unplugged the sole- noid connector and attached a complete internal harness and solenoid assembly “externally” using the battery as a ground (These solenoids are power side controlled and are grounded to the transmission). He erased the codes and started the vehicle. Neither one of the codes returned. He then reattached the vehicle harness to the transmission connector and started the car.


18 // September-October 2021


Figure 4


Both codes returned immediately. This was done several times and each time had the same results. Feeling confident that there was not an external problem in the wiring, he installed the internal harness and sole- noids that was being used in the test. But once the vehicle was started, he had the same codes come up immediately. Checks were then made with all the wiring from the transmission to the com- puter and all was well. The battery system was finally checked but all seemed well there as well. Since he had used the battery ground directly with the external solenoids successfully with his testing procedure, he decided to run a ground wire from the negative post of the battery to the trans- mission as seen in Figures 2, 3 and 4. Although the voltage drop test done on the negative battery cable checked perfectly


fine, there was an apparent path to ground issue with the transmission. Since this ground cable fixed the problem, no fur- ther investigations were made to locate the compromise in the ground path. This was an odd problem indeed. Although checking the battery system wasn’t part of the initial diagnosis, even if it were, this would not have been so quickly discovered. Yet it is another testimony in the importance of power and grounds. Wayne Colonna has been with the Automatic Service Group for over 30 years. As President of ATSG and Director of Quality at ETE REMAN,


Wayne is helping to usher the transmission industry to the highest of standards. When he’s not at ETE in Milwaukee, he can be found with his wife in Miami taking her out to eat, playing Spanish guitar, or maybe enjoying a bottle of fine wine.


Automotive Recycling


SPONSORED


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50  |  Page 51  |  Page 52  |  Page 53  |  Page 54  |  Page 55  |  Page 56  |  Page 57  |  Page 58  |  Page 59  |  Page 60  |  Page 61  |  Page 62  |  Page 63  |  Page 64  |  Page 65  |  Page 66  |  Page 67  |  Page 68  |  Page 69  |  Page 70  |  Page 71  |  Page 72